Ventilating Fans

FRP Industrial Exhausters

Sizes: 17"-60" (fan diameter)
Arrangement: 1
Capacities: To 30,000 CFM
Pressures: To 18" WG
Standard: One piece, solid FRP (fiberglass reinforced plastic) constructed wheels, impact resistant housing.
Accessories: Drains, access door and shaft seals.
Options: Wheels to handle granular or fibrous materials or hot gases.
Application: Corrosive gas handling problems.

Propeller Fans

Sizes: 8" to 24" (fan diameter)
Capacitie: 500 to 4500 CMF
Pressures: To .5" WG
Standard: Direct connected, chrome plated motorslide mount/guard.
Options: Wall shutters.

Volume Fans

Sizes: 8” to 21%’ (fan diameter)
Arrangements: 1 & 10 ’ Capacities: 100 to 4200 CFM
Capacities: 50 to 1800 CFM
Pressures: To 12” WG
Standard: Cast iron housing.
Options: Open steel wheels, flanged aluminum wheels, inlet and outlet flanges, drain, shaft seal, heat slinger, belt guard, motor and drive. Suitable for abrasive and corrosive applications.

Baby Vent Sets

Sizes: 33/4" to 93/le" (fan diameter)
Capacities: 50 to 1800 CFM
Pressures: To 1.75" WG ,fl Direct connected.
Accessories: Housing drain, inlet/outlet screens, heat slinger.
Options: Aluminum or steel wheels and fan cooled (TEFC) or explosion proof (TEXP) motors.
Application: Low pressure intake or exhaust.

Unit Heaters

Sizes: 12" to 24" (fan diameter)
Capacities: 1100 to 4500 CMF, 29,950-275,000 BTU/hr.
Standard: Adjustable louvers, steam, water coils, totally enclosed industrial motor with guard and heavy gauge casing.

Type B

Vaneaxial Fans

Sizes: 15" to 54" (fan diameter)
Arrangement: 9, Belt driven
Capacities: 2500 to 65,000 CFM
Pressures: To 2.5" WG
Accessories: Inlet bells and screens, suspension clips, shaft seals, mounted motor and drive, belt guard, support legs, and sparkproof wheel constuction.
Available: Steel and one piece cast aluminum wheels.

Type BL

Limit-Load

Ventilating Fans

Sizes: 245 to 1200 (fan diameters to 60") SWSI
Arrangement: 1, 3 or 9
Capacities: To 100,000 CFM
Pressures: To full AMCA Class 2 ratings.
Standard: Belt or Direct Drive
Accessories: Door, drain, flanged outlet, shaft seal, type B or C sparkproof construction, split pillow block bearing(s), inlet screen, round or square flanged inlet, heat stinger, mounted motor, drive and guard.
Options: Unistrut motor rails (Arr. 1 unmounted).
Application: Clean air applications requiring AMCA Class 2 certification.

Type E Blowers Exhausters

Sizes: 71/2" to 11' (fan diameter)
Capacities: 60 to 565 CFM
Pressures: To 6" WG
Standard: Cast iron housing (larger units); sheet metal housing (smaller units). Direct connected, 71/2' diameter (2 VEH) supplied with variable speed drive and controller; other sizes with constand speed drives.
Options: Cast iron housing and motor base for small units. Fan cooled (TEFC) or explosion proof (TEXP) motors.
Applications: Low pressure, moderate air volume. Erosive or mildly corrosive gas handling.on.

Industrial Exhausters

Sizes: 12 1/4 to 56" (fan diameter)
Capacities: 270 to 35, 750 CFM
Pressures: To 20" WG
Accessories: Split pillow block bearings, type C spark resistant construction, housing access door, drain, flanged inlet and outlet, shaft seal, heat stinger, OSHA inlet screen, OSHA belt guard, unistrut motor rails, mounted motor and drive.
Options: Wheels designed Erto handle granular, fibrous materials or hot gases.

TYPE BI


centrifugal ventilating fans


FOR CLEAN AIR APPLICATIONS THRU AMCA CLASS 2 PERFORMANCE

non-overloading BI meets today’s require¬ments for ventilating fans with high operating efficiency, quiet operation, versatility of application, rugged con¬struction and built-in ease of maintenance. Arrangement 3, sizes 600 thru 1200 are available in single inlet, single width AMCA Classes 1 and 2, clockwise and counter¬clockwise rotations and top horizontal and upblast discharges. These fans are designed for belt drive or direct drive through a flexible coupling. The BI is complete with a heavy gauge welded steel housing;
torusoidal inlet bell with fixed guide vanes; wheel with single thickness, backwardly-curved airfoil blades and a rugged bearing base. AMCA Class 1 fans are furnished with deep groove ball bearings on sizes 600 thru 1200, AMCA Class 2 fans are furnished with roller bearings on sizes 600 thru 980 and split pillow block roller bear¬ings on sizes 1085 thru 1200. The shaft extends beyond the bearing base and has a keyway for installation of the user’s sheave or coupling. All units are statically and dynamically balanced before shipment.

TYPE BI

centrifugal ventilating fans


FOR CLEAN AIR APPLICATIONS THRU AMCA CLASS 2 PERFORMANCE

non-overIoading BI meets today’s require¬ments for ventilating fans with high operating efficiency, quiet operation, versatility of application, rugged con¬struction and built-in ease of maintenance. Arrangement 1, sizes GOO thru 1200 are available in single inlet, single width AMCA Classes 1 and 2, clockwise and counter¬clockwise rotations and top horizontal and upblast discharges. These fans are designed for belt drive or direct drive through a flexible coupling. The BI is complete with a heavy gauge welded steel housing; torusoidal inlet bell with fixed guide vanes; wheel with single thickness, backwardly-curved airfoil blades and a rugged bearing base. AMCA Class 1 fans are furnished
with deep groove ball bearings on sizes 600 thru 980, roller bearings on size 1085 and split pillow block roller bearings on size 1200. AMCA Class 2 fans are furnished with deep groove ball bearings on sizes 600 thru 730, roller bearings on sizes 805 thru 980 and split pillow block roller bearings on sizes 1085 thru 1200. The shaft extends beyond the bearing base and has a keyway for installation of the user’s sheave or coupling. All units are statically and draamically balanced before ship¬ment. Arrangement 1 BI fans are available with optional unistmt motor rails shipped loose with the fan. The unistrut rails can be shipped loose for permanent mounting to the BI fan bearing base by the fan user.

"PB" & "RPB"

centrifugal ventilating fans

PERFORMANCE DATA

size
max cfm
sp* range
2vpbh
149
to 2"
2pb
200
to 3"
3pb 387
to 5 1/2"
4pb 544
to 6"
4.5pb 700 to 11.1"
5pb 1500 to 23.7"
5.5pb 2800 to 33.0"
6pb 3400 to 35.0"
7pb 8000 to 59.1"
2rpb 300 to 19.9"
3rpb 800 to 30.5"
4rpb
2000 to 48.3"
The 2VEH and 2E fans are supplied with heavy gauge die formed steel housings and motor bases.The 2 VEH is sup¬plied with a variable speed motor (600-3200 RPM) suitable for single phase, 60 Hz, 115 volt operation. The solid state speed controller is shipped loose for field installation.
All nuffoio fans are statically and dynamically balanced prior to shipment.
The “PB” & “RPB” blowersand exhausters are utilized for tlieir industrial range of performance characteristics, with static pressure capabilities from 2 thru 59 inches, and flow capacities from 150 to 8000 CFM.
“PB” & “RPB” fans are widely used in many product or process tea industries for end user and original equipment manufacturers alike. Contact your local Sales Engineer to determine the correcgj^rr I^^fan for your particular application.
The listed blowers are now available in our PDQ fast track shipment program. PDQ program offers one, two, and three week shipments, depending on the required accessories.
Contact your local Sales Engineer for specific construction, performance, and delivery details.

ACCESSORIES

- Drain
- Shaft Seal
- Inlet Screen
- SPB Bearings Arrangment 1
- 600*F Construction
- Flange Inlet
- Flange Outlet
- Paddle Wheel 2RPB
- Double Flange Wheel (3RPB & 4RPB)
- Flange / Back Plate Wheel (4RE-7RE)

ROTATION AND DISCHARGE AVAILABILITY

fan fabricated steel
cast iron
2veh
ccw/bh
-
2e
ccw/bh
cw or ccw*
3e-7e
cw or ccw*
cw or ccw*
2re-4re cw or ccw*
ccw*
* Discharge available in any 45* increment

DIRECT-CONNECTED, CAST IRON HOUSINGS

Baby Vent Sets

ACCESSORIES

HOUSING DRAIN

A 1/2" drilled and tapped hole at the lowest point of the fan scroll to facilitate condensate drainage is available.

INLET/OUTLET SCREENS

Factory mounted hot dipped galvanized steel inlet and outlet screens are available.

HEATSUNGER

Heat slingers reduce heat conduction to the motor bearings which allows higher temperature fan operation. Heat slingers are available on sizes B thru G only.
Canada Blower “Baby Vent Sets” are available in seven sizes to handle any low pressure intake or exhaust application requiring 40 to 1800 CFM. All sizes are constructed with “rugged” cast iron housings, making them ideal for corrosive exhaust. Forward curved wheels are available in aluminum (sizes A-G) or steel (sizes B-G) and are direct connected to the motor shaft. All sizes are available in both clockwise (CW) and counterclockwise (CW) rotation. Discharges can be furnished in any 45° increment. All motors are ball bearing totally enclosed. Both fan cooled (TEFC) and explosion proof (TEXP) are available depending on your particular need. Motors 3/4HP and smaller are either 1/60/115 or 1/60/115-230 while motors 3/4HP and larger are 3/60/230-460. All fans are statically and dynamically balanced by Canada Blower prior to shipment. THE FOLLOWING ARE AVAILABLE WITH EXTENDED DELIVERY: Motor Weather Covers, Vibration Isolators, Stainless Steel Wheels, and Special Coatings including Bisonite M, Phenoflex #957, and Heresite Baked Phenolic. - See more at: http://olegsystems.canadablower.com/tab-2/?preview_id=103&preview_nonce=871e78fbe7&post_format=standard&_thumbnail_id=-1&preview=true#sthash.d0ZnFdQZ.dpuf

INDUSTRIAL EXHAUSTERS


ARRANGEMENTS 1 & 9

SIZES: 17-80 CAPACITY: 270 CFM to 35,750 CFM PRESSURE: Static Pressures to 20” W.G. STANDARD CONSTRUCTION ARRANGEMENT 1 FAN

AVAILABLE WHEEL TYPES

MW - SIZES 17-80

GRANULAR MATERIALS

The radial bladed MW wheel is designed for smooth air flow performance and optimum operating efficiency; The MW wheel is ruggedly built to handle clean air, corrosive fume removal or air-fume mixtures containing granular materials such as grains, dust or abrasive exhaust from grinding or " buffing operations.
OW - SIZES 17-80

FIBROUS MATERIALS

The radial bladed OW cone wheel is fabricated with no front flange. Omission of the flange allows free passage of fibrous materials such as wood shavings, ensilage, paper strips, textile products and other materials which normally tend to clog flanged type wheels.
AW - SIZES 17-80

HOT GASES

The AW wheel is designed for maximum efficiency while handling hot air, gases, fumes - either clean or containing light concentrations of solid materials. The backwardly inclined blades are curved slightly to maintain efficient gas flow through the fan.
OPTIONAL ARRANGEMENT 9 FAN WITH VARIOUS ACCESSORIES AND FACTORY MOUNTED MOTOR AND V-BELT DRIVE
fan with high operating efficiency, versatility of application, rugged constmctionand built-in ease of maintenance. Canada Blower engineers designed Canada Blower Exhauster with these criteria in mind. This line of industrial quality fans offers the ideal solution to the air moving problems of modern industry and represents the result of over 100 years’ experience and engineering leadership in the design and manufacture of air handling equipment.

VOLUME FANS


ARRANGMENT 1

WHEELS

The flanged wheel is built of all riveted construction with two die-formed rims and five die-formed radial blades of heavy gauge steel and a cast steel spider.

HOUSING

The fan housing, shown, is a one piece grey iron casting. The housing inlet plate and drive side plate are also one piece grey iron castings, bolted to the housing. The fan inlet and ou
tlet are designed for slip connection to the user’s duct or standard size pipe.

BEARINGS

Arrangement 1 Volume Fans are equipped with two heavy duty, single row, deep groove grease lubricated ball bearing pillow blocks mounted on a rugged fabricated steel bearing base. The shaft is ground and polished steel with a keyway for installation of the user’s sheave or flexible coupling.

FOR ABRASIVE AND CORROSIVE APPLICATIONS


Canada Blower Volume Fans provide extended service life and reliable performance in punishing applications. A ruggedly contructed cast iron housing and heavy gauge fabricated steel wheel and housing supports enable the Volume Fan to provide long, troublefree service in applications handling hard, gritty, abrasive material in the air stream. Because all housing parts, which come in contact with a contaminated air stream,
are constructed of cast iron, the Volume Fan can be successfully used in applications with corrosive va¬pors present. These fans are particularly adaptable to pneumatic conveying, drying, supplying combustion air, exhausting waste air, gas, vapor and/or materials, ventilating and inflating. The pressure and volume characteristics are more than adequate to handle the requirements usually encountered in this type of work.

Canada Blower axial fans are a cost-effective option for low to medium pressure applications. Roof-mounted models are designed to discharge clean air or fume exhaust up and away from the building. Typical uses are industrial space, warehouses, fume exhaust, and paint booth exhaust. Models are available in spark resistance construction, emergency smoke or continuous high-temperature exhaust. Select from direct and belt drive fans with cast aluminum or fabricated steel blades based upon application requirements.

Inline fan models meet a wide range of supply or exhaust applications in commercial and industrial facilities. There are many models available for clean air, sound sensitive and heavy-duty industrial applications. Units mount in the ceiling or on the floor. Performances range from several hundred cfm to over 100,000 cfm and pressure up to 10 in. wg. Typical building applications include office space, theaters, libraries, lavatories, locker rooms, warehouses, tunnels, parking garages, and kitchen grease. Tube axial inline fans offer a lower cost option and are applied in ducted and unducted commercial or industrial applications. Applications include general ventilation and warehouse or process exhaust involving high temperature or spark resistance are typical applications. Each model includes integral flanges for airtight duct connections and universal mounting brackets to install in any orientation. Mixed flow fans are more efficient than comparable sized centrifugal and axial fans. They operate at lower sound levels with lower operating costs. Greenheck mixed flow models have a range of capabilities and features for different applications.

Canada Blower fan blower ventilator duct tubeaxial vaneaxial high temperature pressure thermo IGE alloy engineering industrial gas garden city circulating circulation oven exhaust plug air kit centrifugal axia

Among the single and multi-stage designs, the two stage variable pitch axial fans with variable blade pitch angle find wide usage in many industrial processes. It is also simple to maintain the fan system as most of the critical parts such as rotor – consisting of the impellers, the main bearing assembly and the propeller blades are isolated as separate units for easy accessibility.
l