FRP FAN Construction

FRP OFFERS THE ADVANTAGES OF FIBERGLASS REINFORCED PLASTIC CONSTRUCTION

Corrosion Resistant Fiberglass Ventilation Fans / Blowers:

Fiberglasss construction is recommended where corrosive elements exist in fume or vapor form. We offer a broad range of products for any corrosive application with time-tested, reliable performance and long-lasting durability. Fiberglass fans are lightweight, yet extremely strong for a long service life. We offer a variety of fiberglass props with an airfoil design, and manufacture the only fiberglass wheel in a solid, one-piece design. We can also provide a moisture-resistant coating (HartKoate) when both moisture and corrosives exist in the airstream.

FRP (fiberglass reinforced plastic) fan construction is receiving increasing recognition for its many advantages in handling corrosives. Primary is the extension of service life many times that of ordinary materials at costs much less than those of stainless steel, special metals and coatings. In addition, impact resistant FRP fan housings are electrically non-conductive and fire retardant. While these and other advantages of FRP blower construction are now available in air handling equipment, it is most important that this equipment be basically sound in design and engineering, as well as in correct selection and application, to render effective, efficient and economical performance.

FRP (fiberglass reinforced plastic) construction is receiving increasing recognition for its many advantages in handling corrosives. Primary is the extension of service life many times that of ordinary materials at costs much less than those of stainless steel, special metals and coatings. In addition, impact resistant FRP fan housings are electrically non-conductive and fire retardant. While these and other advantages of FRP construction are now available in air handling equipment, it is most important that this equipment be basically sound in design and engineering, as well as in correct selection and application, to render effective, efficient and economical performance.

Canada Blower ventilation

Specialized Air Engineering Experience

As can be seen from the typical chemical plant’ pictured here, has had years of experience in supplying all types of air handling equipment for operations involving corrosive materials. These units can be furnished also in steel, special metals and alloys or with a variety of coatings. The most economical and efficient selection is the standard by which air handling equipment will be recommended to assure you of extended satisfactory service at lower operating and maintenance costs.
Canada Blower ventilating

FRP FIBERGLASS FAN WHEELS

Canada Blower radial fan wheel
One-Piece solid FRP MW design fan wheel. Steel hub and shaft through the shaft seal are encapsulated with FRP.
These fans are fabricated from FRP to extend service life under severe operating conditions . . . covering a broad range of corrosives. Blower housings are rotatable and wheels are made of solid FRP except for the steel hub encapsulated in the fan wheel. The shaft, where exposed to gas stream, is FRP encapsulated through the shaft seal. All exterior steel parts are protected with a vinyl coating. Capacities from 300 to 85,000 CFM . . . static pressures to 20”. Ask for bulletin FRP 501A for additional information.

ARRANGEMENT 1 FANS

Canada Blower paddle fan

Featuring the Fiberglass Reinforced Plastic fan housing, type 316 stainless steel bolts imbedded and encapsulated in FRP housing for fastening inlet and drive side stands. Outlet flanges and inlet collar and flanges are solid FRP. Arrangement 1 is designed for belt or direct drive through a flexible coupling. All interior surfaces in contact with a gas stream are FRP. All exposed exterior surfaces are sandblasted, primed and multiple coated with a vinyl coating.

fan accessories

1. The standard drain connection is a threaded coupling type connected to the lowest point of the scroll to facilitate drainage of condensates or other liquids (standard). Flanged drains can be provided (optional). 2. For easy access to the wheel and housing, this FRP neoprene gasketed access door is quickly removed and replaced (optional). 3. Shaft seal of neoprene with FRP backup plate is bolted to the housing to limit gas leakage, but is not gas tight (standard).
4 FRP stuffing boxes and gasketed housing can be provided when standard shaft seal is not adequate (optional). 5 For large motor frames, a structural channel sub-base with integral motor slide base can be supplied in lieu of the standard Arr. 9 pivot base (optional). 6 Two piece, all weather hood protects motor, bearings and drive. Rear section can be tilted to inspect and check belt tension. Construction is vinyl coated steel, (optional on Arr. 10)ventilating.com fanblower.com highpressureblower.net industrialblowerfan.com industrialfanblower.net industrialfanblower.com pressureblower.net northernindustrialsupplycompany.com industrialpressureblower.com tenderall.com chicagoblowercanada.com cbblower.com buffaloblower.com buffalofan.com nis-co.com canadianblower.com olegsystems.com canadablower.com abbblower.com acmefan.net industrialblower.net fansandblowers.net americanblower.net barryfan.com cincinnatifan.net canadafans.com barryfan.netpennbarry.net pennfan.net tcffan.com
.

ARRANGEMENT 9 FANS

Canada Blower material handling fan
Similar in features to Arrangement 1, this “packaged” fan unit features an adjustable motor mount. The steel pivot base assembly provides a rigid motor support and ease of belt tension adjustment which assures perfect sheave alignment.

ARRANGEMENT 10 FANS

Canada Blower radial blower
A “package” fan unit with a limited range of motor sizes, this unit is similar to Arrangement 1 with a variation of the motor mount used on Arrangement 9 fans.

Canada Blower industrial fan accessories

Ventilating Fans
TYPE FL

Canada Blower Class 4 fan wheel
66” diameter design “FRP”-FL rotor — all FRP with encapsulated steel wheel hub. In addition to the complete line of FRP MW Industrial Exhausters, “” “FRP”-FL non-overloading ventilating fans are now available. FRP blower housings are solid fiberglass reinforced plastic. Fan rotors are solid FRP except for the steel hub which is encapsulated in FRP. Shafts are encapsulated in FRP where exposed to the gas stream. Fan housing drain and neoprene shaft seal with FRP backup plate is provided as standard. The inlet and drive side bracing is attached to the FRP housing with type 316 stainless steel bolts which are encapsulated in the housing. The housings are furnished with FRP flanged inlet and outlet for duct connection as standard. Housings are not reversible or rotatable. Discharges may be furnished in 45° increments only.

All exposed metal surfaces are sandblasted, primed and multiple coated with a vinyl protective coating. In addition to arrangement number 1 fans pictured, “FR P”-FL fans can be furnished in Arrangement number 9 with unistrut rails mounted on bearing base for motor and V-belt drive adjustment. For larger motor frames, a structural channel base can be furnished. Sixteen sizes are available with rotors from 12-1/4” to 73” in diameter to cover a wide range of capacities from 900 CFM to 129,000 CFM and static pressure to 6” W.G.

Canada Blower Class IV fan
Arrangement No. 1 size 1320 ‘’FRP”-FL all FRP housing and rotor.
Canada Blower class 4 fan
Arrangement No. 1 size 1320 “FRP”-FL design II fan — inlet side view with protective screen and flanged drain.

Canada Blower

Accessories

1. The standard drain connection is a threaded coupling type connected to the lowest point of the scroll to facilitate drainage of condensates or other liquids (standard). Flanged drains can be provided (optional).
2. For easy access to the wheel and housing, this FRP neoprene gasketed access door is quickly removed and replaced (optional).
3. Shaft seal of neoprene with FRP backup plate is bolted to the housing to limit gas leakage, but is not gas tight (standard).

FRP VENTILATION

FIBERGLASS FANS

Lighter in weight and less costly than “special” metals, they afford a high degree of protection from corrosive fumes responsible for premature failure in metal, rubber lined and protective coated fans. They are ideal for horizontal or vertical installation in interior ductwork and require a minimum of space. Fans are spark tested prior to shipment to assure complete corrosion protection. Capacities from 2000 CFM to 100,000 CFM . . . static pressures to 3”. Ask for bulletin F-305A for additional information.
Canada Blower axial ventilator
FRP Axial fan from entering air side. Durable predrilled inlet and outlet flanges are integrally molded into the fan housing.

FAN SHAFTS are type 316 stainless steel with wheel end threaded for a stainless steel castle nut and cotter pin to hold wheel in place. The shaft and wheel have a keyway to prevent wheel from turning free. The castle nut is further protected with a molded epoxy acorn nut threaded on shaft and sealed in place to fan wheel hub with resin. The seal can easily be broken away by applying a pipe wrench to acorn nut for access to castle nut and wheel removal. After reassembly, this acorn nut can be resealed in place with resin in the field.

SHAFT SEAL is neoprene with molded FRP backup plate held in place with stainless steel bolts and nylon acorn nuts.

FAN BEARINGS – Two antifriction ball bearings completely enclosed within inner cylinder and having grease lines extended to grease fittings outside outer fan casing. These grease lines are completely protected within PVC enclosures from fumes being handled through fan.

MOTOR BASE is a vinyl coated external steel base supported in a rugged FRP support pivoted for belt tension adjustment.

Axial Fans

EFFECTIVE SPACE SAVERS IN DUCT SYSTEM INSTALLATIONS WHERE CORROSION IS A PROBLEM

VANE AXIAL FANS (FRPVA) have molded FRP curved discharge vanes bonded between the inner cylinder and outer casing for maximum fan efficiency, quiet operation and rugged construction

TUBE AXIAL FANS (FRPTA) have extra thick FRP straight discharge vanes serving as struts between the inner cylinder and outer casing. FAN HOUSING — Solid Fiberglass Reinforced Plastic (FRP) construction with integrally bonded FRP flanges, protective belt fairing and inner bearing cylinder. Bearing cylinder has neoprene gasketed removable FRP end covers held in place with stainless steel bolts and nylon acorn nuts and easily removed for adjustment of fan sheave or bearing replacement.

STANDARD FRP FAN WHEELS — On all sizes from 15”through 36” the fan wheel is a one piece fiberglass reinforced molded epoxy wheel duplicating our cast aluminum type “MB” wheel. On sizes 42” through 60”, the basic wheel is a standard steel “MB” wheel encapsulated with FRP. The performance of these fan wheels is identical to standard Type “B” Axial Flow Fans.

ALTERNATE FRP WHEELS — Design 80, 65 or 50 NV wheels have a cast malleable (15” through 42”) or cast steel (48” and 54”) spider encapsulated with FRP molded blades bolted and bonded to encapsulated spider can be furnished on all sizes.

Canada Blower tubeaxial ventilator
Solid FRP support legs are integrally bonded to FRP housing and amply gusseted to support fan, motor and V-belt drive.
Canada Blower duct fan
Internally molded FRP guide vanes assure efficiency and quiet operation while providing rugged support of inner cylinder and belt fairing.

Canada Blower duct fan

TYPE OF STYLE V ROOF VENTILATOR

The addition of a curb plate and style V damper head to an axial fan converts the assembly to an “AF” Type Style V Roof-Vent. Performance is identical to a standard steel AF Roof-Vent. Ask for bulletin RV-200 for additional information. The damper head assembly complete with wind band and flanged stack is fabricated entirely of FIRP with butterfly damper blades pivoted on a stainless steel rod in Teflon bearings.

SO-LOW STLYE V ROOF-VENT FAN

STANDARD FAN WHEELS — Design 80, 65, or 50 NV ventilator wheels have a cast malleable (16” through 42”) or cast steel (48” and 54”) spider encapsulated with FRP molded blades bolted and bonded to the encapsulated spider are basically recommended. Performance of these wheels is identical to standard So-Low Style “V” “NV” Roof-Vents.

SPECIAL CURBS — for peaked or sloped roof mounting can be furnished at extra cost.

DISCHARGE STACKS — When it is deemed advisable to jet the fumes being discharged through a roof mounted unit at some elevation above the roof level, a discharge stack can be provided fabricated entirely of FRP for mounting on the Curb-Stack Assembly in lieu of the Damper Head Assembly. Gussets would be provided near discharge end of stack for attachment of guywire anchors which would be required. If desired, the discharge end can be necked down to provide a higher discharge velocity. Do NOT exceed 10 feet in stack height without checking factory.
Canada Blower duct fan
Weather cover (FRP) fastens in place with stainless steel ware and is easily removed for access to motor and drive.
Canada Blower duct blower

Flanged curb plate is integrally bonded to housing and can be hard-furnished for flat, sloped or peaked roofs.

FRP BLOWER CONSTRUCTION

Canada Blower FRP blower
Size 65-4 FRP “CB” arrangement 9 blower with rubber lined rotor, common structural steel subbase, access door, drain and totally enclosed belt guard.
Canada Blower fiberglass blower

Size 40-3 FRP “CB” arrangement 1 blower arranged for direct connection through a flexible coupling, Titanium wheel with a Hastelloy C shaft, access door, drain, outlet cone and coupling guard.
Canada Blower FRP pressure blower
Size 6 FRP type “E” arrangement 1 for direct connection through flexible coupling or V-belt drive. Special feature includes an FRP stuffing box for prevention of gas leakage around the shaft.

PRESSURE BLOWERS

TYPE FRP “CB” HIGH PRESSURE BLOWERS

Type FRP “CB” high pressure blowers are furnished with a solid FRP housing. Steel bracing is attached to the FRP housing with type 316 stainless steel bolts encapsulated in FRP blower housing. Rotating assembly can be furnished in special metal or rubber lined for severe corrosive environments. All exposed external metal surfaces are sandblasted, primed and multiple coated with a vinyl protective coating. Static pressures to 100 inches W.G. plus and capacities to 50,000 CFM. Ask for bulletin FI-310 for additional information.

TYPE FRP “E” and “RE” PRESSURE BLOWERS

Type FRP “E” and FRP “RE” pressure blowers are available, capacities to 3,300 CFM. Static pressures to 29” W.G. with FRP rotors, and up to 47” W.G. with special metal rotors. All housings are fiberglass reinforced plastic with a steel drive side plate. Drive side plate is attached to the FRP housing with type 316 stainless steel bolts encapsulated in FRP housing. All exterior metal surfaces are sandblasted, primed and multiple coated with a vinyl protective coating. Ask for bulletin FI-411 for additional information.
Canada Blower fiberglass pressure blower
Size 4 FRP “RE” arrangement 8 FRP blower with bearing base extended for direct connection of motor through a flexible coupling.

Canada Blower FRP high pressure blower
Size FRP “CB” arrangement 8 FRP blower, Titanium wheel and shaft, coupling guard and carbon ring shaft seal (not pictured).

STANDARD RESINS OF FRP FAN CONSTRUCTION

*Polyester—Hetron 92 by Hooker Electrochemical Co. Atlac 382-05 by Atlas Chemical Division, ICI America, Inc. *Epoxy —by Bisonite Company, Inc. NOTE; Other Polyesters and Epoxies available upon request or as required where standard resins are not suitable.

Physical Properties

ASTM TEST METHOD MINIMUM PROPERTIES
D-638 Tensile Strength, psi 12,000
D-790 Flexural Strength, psi 20,000
D-695 Compressive Strength, psi 20,000
D-790 Modulus of Elasticity in Flexural, psi 8×10^5
D-785 Hardness – Barcol 40

STANDARD RESINS OF FIBERGLASS BLOWER CONSTRUCTION

*Polyester—Hetron 92 by Hooker Electrochemical Co. Atlac 382-05 by Atlas Chemical Division, ICI America, Inc. *Epoxy —by Bisonite Company, Inc. NOTE; Other Polyesters and Epoxies available upon request or as required where standard resins are not suitable.

Physical Properties

ASTM TEST METHOD MINIMUM PROPERTIES
D-638 Tensile Strength, psi 12,000
D-790 Flexural Strength, psi 20,000
D-695 Compressive Strength, psi 20,000
D-790 Modulus of Elasticity in Flexural, psi 8×10^5
D-785 Hardness – Barcol 40

Chemical Resistance

Applications of corrosion engineering to air moving engineering is becoming more important daily in eliminating costly replacements, shut down time and fume control of many new and varied chemical processes. We have prepared a chemical resistance chart which we offer as a guide to plant engineers in evaluating our standard Fiber- glass equipment. These standards were selected for the widest possible range of chemical service commensurate with the best practice in mechanical constructions, design and economy.
NOTE: This guide is provided as a customer service and definitely should NOT be construed as any guarantee by the against damage due to corrosion, abrasion or erosion as per our standard terms of sale.
This guide chart also attempts to point out as many known limitations as possible, pertaining to standard construction. This does not mean however that is limited to these standards only, but can furnish special FRP fabrication upon request. Test panels can readily be made available for test work in unusual applications and many plastic materials are available for special fabrication in a wide variety of Epoxy and Polyester-Fiberglass compounds. We further wish to call attention to the fact that even though some chemical attack is evident on plastic materials under immersion conditions, application of this material may still give longer or more satisfactory service than conventional metals or coated equipment in contaminated air or gaseous conditions. Two typical examples from field service are as follows:

1. It is well established that some chemical attack is evidenced on panels immersed in nitric acid and hydrofluoric acid concentrated at elevated temperatures; and yet plastic construction on exhaust hoods, fans and ducts over wash tanks containing these acids are still in excellent condition after three years service.

2. Certain chlorinated solvents will attack and decompose our standard resin materials on immersion and yet chloroform and methylene chloride fumes are exhausted in laboratory exhaust systems with years of satisfactory service.

Why use Fiberglass reinforced resin structures? Corrosion of metals produces a new chemical product of metallic salt or oxide which grows and deforms the metallic structure. Coating of metals gives a delaying effect to this corrosion which often extends the useful life of the equipment to satisfactory service. However, all plastic construction produces a solid plastic structure to eliminate all metallic corrosion. fans are carefully engineered to eliminate all metallic contact with the air stream which is essential for long life corrosion resistance.

Immersion Saturavad Vapor Unsafurated Vapor or
Dust in Air Mixtures
Acids
Acetic, 5% S S S
Acetic, 10% S S S*
Acetic Glacial U U L*
Acetic Anhydride, Conc U U L*
Aqua Regia (HN03-HCI) 3:1 U L S*
Benzene Sulfonic, Conc s s s
Benzene Sulfonic, 25% s s s
Benzoic, Conc s s s
Boric s s s
Butyricm, Conc s s s
Butyric, 25% s s s
Carbonic s s s
Chloroacetic, Conc U L S*
Chlorosulfonic Acid, 100% U U L*
Chromic, 10% S S S
Chromic, 50% S S S
Citric, all concentrations S S S
Cresylic U U L*
Fatty, c^6 and up S S S
Fluosilicic U S S
Formic 10% S S S
Formic, 50% and above U U S*
Formic,25% and above U S S*
Hyrdobromic, up to 50% S U S
Hydrochloric, Conc L S S
Hydrochloric, 10% S S S
Hydrocyanic, all concentrations S S S
Hypochlorous, 5% S S S
Hydrofluoric, 40% U L S*
HydroFluoric, 10% U S S*
Lactic, all concentrations S S S
Maleic, all concentrations S S S
Nitric, 5% S S S
Nitric, 10% S S S*
Nitric,20% S S S*
Nitric, 40% U L S*
Oleic, Conc. S S S
Oxalic, all concentrations S S S
Prechloric, up to 25% NR NR S*+++
Phentol, above 10% U S S*
Phosphoric, all concentrations S S S
Picric 10% NR NR S*+++
Picric 10% in alcohol S*+++
Stearic, conc S S S
Sulfuric, 3% S S S
Sulfuric, 30% S S S
Sulfuric, 50% S S S
Sulfuric, 70% L S S
Sulfuric, 93% U U L
H2SO4 – HNO3 Pickling Solution S S S
Tartaric Acid, all conc S S S
ACID SALTS
Alum. all conc S S S
Ammonium Chloride, all conc S S S
Ammonium Sulfate, all conc S S S
Copper Chloride, all conc S S S
Copper sulfate, all conc S S S
Ferric Chloride, all conc S S S
Ferric Sulfate, all conc S S S
Nickel Chloride, all conc S S S
Nickel Nitrate S S S
Nickel Sulfate, all conc S S S
Stannic Chloride, 100% S S S*
Stannous Chloride, all conc S S S
Zinc Chloride, all conc S S S
Zinc Sulfate, all conc S S S
NATURAL SALTS s s s
Barium Chloride, all conc s s s
Calcium Chloride, all conc s s s
Calcium Sulfate, all conc s s s
Lithium Chloride s s S
Magnesium Chloride, all conc S S S
Magnesium Sulfate, all conc S S S
Mercuric Chloride S S S
Possadium Chloride, all conc S S SS
Possadium Nitrate, all conc S S S
Possadium Sulfate, all conc S S S
Silver Nitrate S S S
Sodium Chloride, all conc S S S
Sodium Nitrate, all conc S S S
Sodium Sulfate, all conc S S S
Sodium Sulfate, 25% L L S*
ALKALNE SALTS
Sodium Bicarbonate 100% s s s
Sodium Bicarbonate 10% s s s
Sodium Carbonate 2% s s s*
Sodium Chloride, Ph 11 u s s*
Sodium Cyanite u l s*
Sodium Sulphide, 25% and above s s s
Sodium Suphade, 10% s s s
Trisodium Phosphate conc l s s*
Trisodium Phosphat, 10% s s s*

Canada Blower Company is a distributor of ventilation equipment. Canada Blower stocks a complete range of axial propeller and centrifugal fans and other air moving equipment in our own warehouse:

-Ventilating & Process Fans
-Industrial Exhausters
-Fixed Pitch Tube-axial and Vane-axial Fans
-Plug & Plenum Fans
-Inline Centrifugal Fans
-Upblast & Hooded Roof Fans
-Bifurcator Exhaust Fans
-HyBlast Exhaust Fans
-Special Metals Fans
-Ventilating & Process Fans
-Industrial Exhausters
-Fixed Pitch Axial Fans
-Plug Fans
-Inline Centrifugal Fans
-Special Metal Fans
-Custom Air Handling Units
-Modular Air Handling Units
-Evaporative Cooling Units
-Sprayed Coil Units
-Cooling Coils
-Steam and Hot Water Heating Coils
-Integral Face and Bypass Coils
-Code Stamped Coils
-Fluid Coolers

ventilator fan blower reversible exhaust supply roof hooded propeller industrial exhauster